display werkt, bltouch nog niet
This commit is contained in:
parent
58dd2d9cd7
commit
695493ce9b
151
printer.cfg
Normal file
151
printer.cfg
Normal file
@ -0,0 +1,151 @@
|
||||
# This file contains pin mappings for the stock 2020 Creality Ender 3
|
||||
# V2. To use this config, during "make menuconfig" select the
|
||||
# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
|
||||
# communication.
|
||||
|
||||
# If you prefer a direct serial connection, in "make menuconfig"
|
||||
# select "Enable extra low-level configuration options" and select
|
||||
# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
|
||||
# cable used for the LCD module as follows:
|
||||
# 3: Tx, 4: Rx, 9: GND, 10: VCC
|
||||
|
||||
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
||||
# turning on the printer with the card inserted. The firmware
|
||||
# filename must end in ".bin" and must not match the last filename
|
||||
# that was flashed.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
[include mainsail.cfg]
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PB9
|
||||
dir_pin: PC2
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PA5
|
||||
position_endstop: -20
|
||||
position_min: -20
|
||||
position_max: 235
|
||||
homing_speed: 100
|
||||
second_homing_speed: 10
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB7
|
||||
dir_pin: PB8
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PA6
|
||||
position_endstop: -8
|
||||
position_min: -8
|
||||
position_max: 235
|
||||
homing_speed: 100
|
||||
second_homing_speed: 10
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB6
|
||||
dir_pin: !PB5
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
#position_endstop: 0.0
|
||||
position_min: -5
|
||||
position_max: 250
|
||||
|
||||
[extruder]
|
||||
max_extrude_only_distance: 100.0
|
||||
step_pin: PB3
|
||||
dir_pin: PB4
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PA1
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC5
|
||||
control: pid
|
||||
pid_Kp: 21.527
|
||||
pid_Ki: 1.063
|
||||
pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA2
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC4
|
||||
control: pid
|
||||
pid_Kp: 54.027
|
||||
pid_Ki: 0.770
|
||||
pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: PA0
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
EXP1_1=PC6,EXP1_3=PB10,EXP1_5=PB14,EXP1_7=PB12,EXP1_9=<GND>,
|
||||
EXP1_2=PB2,EXP1_4=PB11,EXP1_6=PB13,EXP1_8=PB15,EXP1_10=<5V>,
|
||||
PROBE_IN=PB1,PROBE_OUT=PB0,FIL_RUNOUT=PC6
|
||||
|
||||
|
||||
######################################################################
|
||||
# 128x64 Full Graphic Creality CR10 / ENDER 3 stockdisplay
|
||||
######################################################################
|
||||
|
||||
# This section is used for a Creality "12864" display with a single
|
||||
# ribbon cable between the display's EXP3 plug and the
|
||||
# micro-controller board's EXP1 connector.
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: EXP1_7
|
||||
sclk_pin: EXP1_6
|
||||
sid_pin: EXP1_8
|
||||
encoder_pins: ^EXP1_5, ^EXP1_3
|
||||
click_pin: ^!EXP1_2
|
||||
|
||||
[output_pin beeper]
|
||||
pin: EXP1_1
|
||||
|
||||
[display_status]
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PROBE_IN
|
||||
control_pin: PROBE_OUT
|
||||
x_offset: -40
|
||||
y_offset: -12
|
||||
z_offset: 0
|
||||
probe_with_touch_mode: true
|
||||
stow_on_each_sample: false
|
||||
pin_up_touch_mode_reports_triggered: true
|
||||
|
||||
[bed_mesh]
|
||||
speed: 120
|
||||
mesh_min: 10, 10
|
||||
mesh_max: 195, 220
|
||||
probe_count: 4,4
|
||||
algorithm: bicubic
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 157.5,129.5
|
||||
speed: 75
|
||||
z_hop: 10
|
||||
z_hop_speed: 5
|
||||
move_to_previous: true
|
Loading…
Reference in New Issue
Block a user