Merge branch 'main' of git.iky.nl:Ton/Ender3

Ik weet ook niet wat er nu weer mis ging. Git is hard

printer.cfg

@@ -0,0 +1,151 @@
+# This file contains pin mappings for the stock 2020 Creality Ender 3
+# V2. To use this config, during "make menuconfig" select the
+# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
+# communication.
+
+# If you prefer a direct serial connection, in "make menuconfig"
+# select "Enable extra low-level configuration options" and select
+# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
+# cable used for the LCD module as follows:
+# 3: Tx, 4: Rx, 9: GND, 10: VCC
+
+# Flash this firmware by copying "out/klipper.bin" to a SD card and
+# turning on the printer with the card inserted. The firmware
+# filename must end in ".bin" and must not match the last filename
+# that was flashed.
+
+# See docs/Config_Reference.md for a description of parameters.
+[include mainsail.cfg]
+
+[stepper_x]
+step_pin: PB9
+dir_pin: PC2
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PA5
+position_endstop: -20
+position_min: -20
+position_max: 235
+homing_speed: 100
+second_homing_speed: 10
+
+[stepper_y]
+step_pin: PB7
+dir_pin: PB8
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PA6
+position_endstop: -8
+position_min: -8
+position_max: 235
+homing_speed: 100
+second_homing_speed: 10
+
+[stepper_z]
+step_pin: PB6
+dir_pin: !PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 8
+endstop_pin: probe:z_virtual_endstop
+#position_endstop: 0.0
+position_min: -5
+position_max: 250
+
+[extruder]
+max_extrude_only_distance: 100.0
+step_pin: PB3
+dir_pin: PB4
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 33.500
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA1
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+control: pid
+pid_Kp: 21.527
+pid_Ki: 1.063
+pid_Kd: 108.982
+min_temp: 0
+max_temp: 250
+
+[heater_bed]
+heater_pin: PA2
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: pid
+pid_Kp: 54.027
+pid_Ki: 0.770
+pid_Kd: 948.182
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: PA0
+
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
+restart_method: command
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+[board_pins]
+aliases:
+  EXP1_1=PC6,EXP1_3=PB10,EXP1_5=PB14,EXP1_7=PB12,EXP1_9=<GND>,
+  EXP1_2=PB2,EXP1_4=PB11,EXP1_6=PB13,EXP1_8=PB15,EXP1_10=<5V>,
+  PROBE_IN=PB1,PROBE_OUT=PB0,FIL_RUNOUT=PC6
+
+  
+######################################################################
+# 128x64 Full Graphic Creality CR10 / ENDER 3 stockdisplay
+######################################################################
+
+# This section is used for a Creality "12864" display with a single
+# ribbon cable between the display's EXP3 plug and the
+# micro-controller board's EXP1 connector.
+
+[display]
+lcd_type: st7920
+cs_pin: EXP1_7
+sclk_pin: EXP1_6
+sid_pin: EXP1_8
+encoder_pins: ^EXP1_5, ^EXP1_3
+click_pin: ^!EXP1_2
+
+[output_pin beeper]
+pin: EXP1_1
+
+[display_status]
+
+[bltouch]
+sensor_pin: ^PROBE_IN
+control_pin: PROBE_OUT
+x_offset: -40
+y_offset: -12
+z_offset: 0
+probe_with_touch_mode: true
+stow_on_each_sample: false
+pin_up_touch_mode_reports_triggered: true
+
+[bed_mesh]
+speed: 120
+mesh_min: 10, 10
+mesh_max: 195, 220
+probe_count: 4,4
+algorithm: bicubic
+
+[safe_z_home]
+home_xy_position: 157.5,129.5
+speed: 75
+z_hop: 10
+z_hop_speed: 5
+move_to_previous: true