printer.cfg

@@ -1,151 +0,0 @@
-# This file contains pin mappings for the stock 2020 Creality Ender 3
-# V2. To use this config, during "make menuconfig" select the
-# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
-# communication.
-
-# If you prefer a direct serial connection, in "make menuconfig"
-# select "Enable extra low-level configuration options" and select
-# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
-# cable used for the LCD module as follows:
-# 3: Tx, 4: Rx, 9: GND, 10: VCC
-
-# Flash this firmware by copying "out/klipper.bin" to a SD card and
-# turning on the printer with the card inserted. The firmware
-# filename must end in ".bin" and must not match the last filename
-# that was flashed.
-
-# See docs/Config_Reference.md for a description of parameters.
-[include mainsail.cfg]
-
-[stepper_x]
-step_pin: PB9
-dir_pin: PC2
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 40
-endstop_pin: ^PA5
-position_endstop: -20
-position_min: -20
-position_max: 235
-homing_speed: 100
-second_homing_speed: 10
-
-[stepper_y]
-step_pin: PB7
-dir_pin: PB8
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 40
-endstop_pin: ^PA6
-position_endstop: -8
-position_min: -8
-position_max: 235
-homing_speed: 100
-second_homing_speed: 10
-
-[stepper_z]
-step_pin: PB6
-dir_pin: !PB5
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 8
-endstop_pin: probe:z_virtual_endstop
-#position_endstop: 0.0
-position_min: -5
-position_max: 250
-
-[extruder]
-max_extrude_only_distance: 100.0
-step_pin: PB3
-dir_pin: PB4
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 33.500
-nozzle_diameter: 0.400
-filament_diameter: 1.750
-heater_pin: PA1
-sensor_type: EPCOS 100K B57560G104F
-sensor_pin: PC5
-control: pid
-pid_Kp: 21.527
-pid_Ki: 1.063
-pid_Kd: 108.982
-min_temp: 0
-max_temp: 250
-
-[heater_bed]
-heater_pin: PA2
-sensor_type: EPCOS 100K B57560G104F
-sensor_pin: PC4
-control: pid
-pid_Kp: 54.027
-pid_Ki: 0.770
-pid_Kd: 948.182
-min_temp: 0
-max_temp: 130
-
-[fan]
-pin: PA0
-
-[mcu]
-serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
-restart_method: command
-
-[printer]
-kinematics: cartesian
-max_velocity: 300
-max_accel: 3000
-max_z_velocity: 5
-max_z_accel: 100
-
-[board_pins]
-aliases:
-  EXP1_1=PC6,EXP1_3=PB10,EXP1_5=PB14,EXP1_7=PB12,EXP1_9=<GND>,
-  EXP1_2=PB2,EXP1_4=PB11,EXP1_6=PB13,EXP1_8=PB15,EXP1_10=<5V>,
-  PROBE_IN=PB1,PROBE_OUT=PB0,FIL_RUNOUT=PC6
-
-  
-######################################################################
-# 128x64 Full Graphic Creality CR10 / ENDER 3 stockdisplay
-######################################################################
-
-# This section is used for a Creality "12864" display with a single
-# ribbon cable between the display's EXP3 plug and the
-# micro-controller board's EXP1 connector.
-
-[display]
-lcd_type: st7920
-cs_pin: EXP1_7
-sclk_pin: EXP1_6
-sid_pin: EXP1_8
-encoder_pins: ^EXP1_5, ^EXP1_3
-click_pin: ^!EXP1_2
-
-[output_pin beeper]
-pin: EXP1_1
-
-[display_status]
-
-[bltouch]
-sensor_pin: ^PROBE_IN
-control_pin: PROBE_OUT
-x_offset: -40
-y_offset: -12
-z_offset: 0
-probe_with_touch_mode: true
-stow_on_each_sample: false
-pin_up_touch_mode_reports_triggered: true
-
-[bed_mesh]
-speed: 120
-mesh_min: 10, 10
-mesh_max: 195, 220
-probe_count: 4,4
-algorithm: bicubic
-
-[safe_z_home]
-home_xy_position: 157.5,129.5
-speed: 75
-z_hop: 10
-z_hop_speed: 5
-move_to_previous: true