119 lines
8.1 KiB
C
119 lines
8.1 KiB
C
|
/*
|
||
|
|
user_config_override.h - user configuration overrides my_user_config.h for Tasmota
|
||
|
|
|
||
|
|
Copyright (C) 2021 Theo Arends
|
||
|
|
|
||
|
|
This program is free software: you can redistribute it and/or modify
|
||
|
|
it under the terms of the GNU General Public License as published by
|
||
|
|
the Free Software Foundation, either version 3 of the License, or
|
||
|
|
(at your option) any later version.
|
||
|
|
|
||
|
|
This program is distributed in the hope that it will be useful,
|
||
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
|
GNU General Public License for more details.
|
||
|
|
|
||
|
|
You should have received a copy of the GNU General Public License
|
||
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#ifndef _USER_CONFIG_OVERRIDE_H_
|
||
|
|
#define _USER_CONFIG_OVERRIDE_H_
|
||
|
|
|
||
|
|
/*****************************************************************************************************\
|
||
|
|
* USAGE:
|
||
|
|
* To modify the stock configuration without changing the my_user_config.h file:
|
||
|
|
* (1) copy this file to "user_config_override.h" (It will be ignored by Git)
|
||
|
|
* (2) define your own settings below
|
||
|
|
*
|
||
|
|
******************************************************************************************************
|
||
|
|
* ATTENTION:
|
||
|
|
* - Changes to SECTION1 PARAMETER defines will only override flash settings if you change define CFG_HOLDER.
|
||
|
|
* - Expect compiler warnings when no ifdef/undef/endif sequence is used.
|
||
|
|
* - You still need to update my_user_config.h for major define USE_MQTT_TLS.
|
||
|
|
* - All parameters can be persistent changed online using commands via MQTT, WebConsole or Serial.
|
||
|
|
\*****************************************************************************************************/
|
||
|
|
|
||
|
|
|
||
|
|
// -- Setup your own Wifi settings ---------------
|
||
|
|
#undef STA_SSID1
|
||
|
|
#define STA_SSID1 "Online.nl_1C91" // [Ssid1] Wifi SSID
|
||
|
|
|
||
|
|
#undef STA_PASS1
|
||
|
|
#define STA_PASS1 "8G87B4447B" // [Password1] Wifi password
|
||
|
|
|
||
|
|
// -- Setup your own MQTT settings ---------------
|
||
|
|
#undef MQTT_HOST
|
||
|
|
#define MQTT_HOST "192.168.1.121" // [MqttHost]
|
||
|
|
|
||
|
|
#undef MQTT_PORT
|
||
|
|
#define MQTT_PORT 1883 // [MqttPort] MQTT port (10123 on CloudMQTT)
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
#define USE_LVGL // LVGL Engine, requires Berry (+382KB)
|
||
|
|
#define USE_LVGL_PSRAM // Allocate LVGL memory in PSRAM if PSRAM is connected - this might be slightly slower but leaves main memory intact
|
||
|
|
#define USE_LVGL_HASPMOTA // Enable OpenHASP compatiblity and Robotocondensed fonts (+90KB flash)
|
||
|
|
#define USE_LVGL_MAX_SLEEP 10 // max sleep in ms when LVGL is enabled, more than 10ms will make display less responsive
|
||
|
|
#define USE_LVGL_PNG_DECODER // include a PNG image decoder from file system (+16KB)
|
||
|
|
#define USE_LVGL_TOUCHSCREEN // Use virtual touch screen with Berry driver
|
||
|
|
#define USE_LVGL_FREETYPE // Use the FreeType renderer to display fonts using native TTF files in file system (+77KB flash)
|
||
|
|
#define LV_USE_FT_CACHE_MANAGER 1 // define whether glyphs are cached by FreeType library
|
||
|
|
#define USE_LVGL_FREETYPE_MAX_FACES 64 // max number of FreeType faces in cache
|
||
|
|
#define USE_LVGL_FREETYPE_MAX_SIZES 4 // max number of sizes in cache
|
||
|
|
#define USE_LVGL_FREETYPE_MAX_BYTES 16*1024 // max bytes in cache
|
||
|
|
#define USE_LVGL_FREETYPE_MAX_BYTES_PSRAM 64*1024 // max bytes in cache when using PSRAM
|
||
|
|
#define USE_LVGL_BG_DEFAULT 0x000000 // Default color for the uninitialized background screen (black)
|
||
|
|
|
||
|
|
|
||
|
|
#define USE_BERRY // Enable Berry scripting language
|
||
|
|
|
||
|
|
#define USE_INA219 // [I2cDriver14] Enable INA219 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+1k code)
|
||
|
|
#define INA219_SHUNT_RESISTOR (0.100) // 0.1 Ohm default shunt resistor, can be overriden in user_config_override or using Sensor13
|
||
|
|
#define USE_INA226 // [I2cDriver35] Enable INA226 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+2k3 code)
|
||
|
|
|
||
|
|
#define USE_MCP230xx // [I2cDriver22] Enable MCP23008/MCP23017 - Must define I2C Address in #define USE_MCP230xx_ADDR below - range 0x20 - 0x27 (+5k1 code)
|
||
|
|
#define USE_MCP230xx_ADDR 0x20 // Enable MCP23008/MCP23017 I2C Address to use (Must be within range 0x20 through 0x26 - set according to your wired setup)
|
||
|
|
#define USE_MCP230xx_OUTPUT // Enable MCP23008/MCP23017 OUTPUT support through sensor29 commands (+2k2 code)
|
||
|
|
#define USE_MCP230xx_DISPLAYOUTPUT // Enable MCP23008/MCP23017 to display state of OUTPUT pins on Web UI (+0k2 code)
|
||
|
|
#define USE_MCP23XXX_DRV // [I2cDriver77] Enable MCP23xxx support as virtual switch/button/relay (+3k(I2C)/+5k(SPI) code)
|
||
|
|
#define USE_PCA9685 // [I2cDriver1] Enable PCA9685 I2C HW PWM Driver - Must define I2C Address in #define USE_PCA9685_ADDR below - range 0x40 - 0x47 (+1k4 code)
|
||
|
|
#define USE_PCA9685_ADDR 0x40 // Enable PCA9685 I2C Address to use (Must be within range 0x40 through 0x47 - set according to your wired setup)
|
||
|
|
#define USE_PCA9685_FREQ 50 // Define default PWM frequency in Hz to be used (must be within 24 to 1526) - If other value is used, it will rever to 50Hz
|
||
|
|
#define USE_PCA9632 // [I2cDriver75] Enable PCA9632 I2C HW PWM Driver (+1k8 code)
|
||
|
|
#define USE_PCA9632_ADDR 0x60 // Define PCA9685 I2C Address to use (Must be within range 0x60 through 0x63 - set according to your wired setup)
|
||
|
|
#define USE_PCA9632_CM_0 0 // Mapping for channel 0
|
||
|
|
#define USE_PCA9632_CM_1 1 // Mapping for channel 1
|
||
|
|
#define USE_PCA9632_CM_2 2 // Mapping for channel 2
|
||
|
|
#define USE_PCA9632_CM_3 3 // Mapping for channel 3
|
||
|
|
|
||
|
|
#define USE_PCF8574 // [I2cDriver2] Enable PCF8574 I/O Expander (I2C addresses 0x20 - 0x26 and 0x39 - 0x3F) (+2k1 code)
|
||
|
|
#define USE_PCF8574_MODE2 // Enable Mode2 virtual relays/buttons/switches (+2k3 code)
|
||
|
|
#define USE_PCF8574_SENSOR // Enable Mode1 inputs and outputs in SENSOR message (+0k2 code)
|
||
|
|
#define USE_PCF8574_DISPLAYINPUT // Enable Mode1 inputs display in Web page (+0k2 code)
|
||
|
|
#define USE_PCF8574_MQTTINPUT // Enable Mode1 MQTT message & rule process on input change detection : stat/%topic%/PCF8574_INP = {"Time":"2021-03-07T16:19:23+01:00","PCF8574-1_INP":{"D1":1}} (+0k5 code)
|
||
|
|
#define PCF8574_ADDR1 0x20 // First address to search for PCF8574
|
||
|
|
#define PCF8574_ADDR1_COUNT 7 // Number of addresses to search for PCF8574 - Default to 0x20 to 0x26
|
||
|
|
#define PCF8574_ADDR2 0x39 // First address to search for PCF8574A
|
||
|
|
#define PCF8574_ADDR2_COUNT 6 // Number of addresses to search for PCF8574A - Default to 0x39 to 0x3E
|
||
|
|
|
||
|
|
// #define USE_DISPLAY // Add I2C/TM1637/MAX7219 Display Support (+2k code)
|
||
|
|
// #define USE_DISPLAY_TM1637 // [DisplayModel 15] Enable TM1637 Module
|
||
|
|
// #define USE_DISPLAY_MAX7219 // [DisplayModel 19] Enable MAX7219 Module
|
||
|
|
|
||
|
|
// -- Universal Display Driver ---------------------------------
|
||
|
|
// #define USE_UNIVERSAL_DISPLAY // New universal display driver for both I2C and SPI
|
||
|
|
#define MAX_TOUCH_BUTTONS 16 // Virtual touch buttons
|
||
|
|
|
||
|
|
// -- SPI sensors ---------------------------------
|
||
|
|
#define USE_SPI // Hardware SPI using GPIO12(MISO), GPIO13(MOSI) and GPIO14(CLK) in addition to two user selectable GPIOs(CS and DC)
|
||
|
|
|
||
|
|
#ifdef USE_SPI
|
||
|
|
#define USE_DISPLAY // Add SPI Display support for 320x240 and 480x320 TFT
|
||
|
|
#define USE_DISPLAY_ILI9341 // [DisplayModel 4] Enable ILI9341 Tft 480x320 display (+19k code)
|
||
|
|
#define USE_DISPLAY_ST7789 // [DisplayModel 12] Enable ST7789 module
|
||
|
|
#endif
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
#endif // _USER_CONFIG_OVERRIDE_H_
|