405 lines
12 KiB
INI
405 lines
12 KiB
INI
# generated by PrusaSlicer 2.6.1+win64 on 2023-10-25 at 07:12:44 UTC
|
|
|
|
[print:0.2mm-KLP1]
|
|
avoid_crossing_curled_overhangs = 1
|
|
avoid_crossing_perimeters = 0
|
|
avoid_crossing_perimeters_max_detour = 0
|
|
bottom_fill_pattern = monotonic
|
|
bottom_solid_layers = 3
|
|
bottom_solid_min_thickness = 0
|
|
bridge_acceleration = 4000
|
|
bridge_angle = 0
|
|
bridge_flow_ratio = 1
|
|
bridge_speed = 60
|
|
brim_separation = 0.02
|
|
brim_type = outer_only
|
|
brim_width = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
complete_objects = 0
|
|
default_acceleration = 10000
|
|
dont_support_bridges = 1
|
|
draft_shield = disabled
|
|
elefant_foot_compensation = 0.15
|
|
enable_dynamic_overhang_speeds = 1
|
|
external_perimeter_acceleration = 2000
|
|
external_perimeter_extrusion_width = 0.42
|
|
external_perimeter_speed = 100
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 1
|
|
extra_perimeters_on_overhangs = 0
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extrusion_width = 0.42
|
|
fill_angle = 45
|
|
fill_density = 13%
|
|
fill_pattern = gyroid
|
|
first_layer_acceleration = 500
|
|
first_layer_acceleration_over_raft = 0
|
|
first_layer_extrusion_width = 0.5
|
|
first_layer_height = 0.2
|
|
first_layer_speed = 50
|
|
first_layer_speed_over_raft = 30
|
|
fuzzy_skin = none
|
|
fuzzy_skin_point_dist = 0.8
|
|
fuzzy_skin_thickness = 0.3
|
|
gap_fill_enabled = 1
|
|
gap_fill_speed = 200
|
|
gcode_comments = 0
|
|
gcode_label_objects = 1
|
|
gcode_resolution = 0.0125
|
|
gcode_substitutions =
|
|
infill_acceleration = 5000
|
|
infill_anchor = 400%
|
|
infill_anchor_max = 20
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0.45
|
|
infill_first = 0
|
|
infill_overlap = 7%
|
|
infill_speed = 220
|
|
inherits =
|
|
interface_shells = 0
|
|
ironing = 0
|
|
ironing_flowrate = 15%
|
|
ironing_spacing = 0.1
|
|
ironing_speed = 15
|
|
ironing_type = top
|
|
layer_height = 0.2
|
|
max_print_speed = 500
|
|
max_volumetric_extrusion_rate_slope_negative = 0
|
|
max_volumetric_extrusion_rate_slope_positive = 0
|
|
max_volumetric_speed = 0
|
|
min_bead_width = 85%
|
|
min_feature_size = 25%
|
|
min_skirt_length = 0
|
|
mmu_segmented_region_interlocking_depth = 0
|
|
mmu_segmented_region_max_width = 0
|
|
notes =
|
|
only_retract_when_crossing_perimeters = 0
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base]_{filament_type[0]}_{print_time}.gcode
|
|
overhang_speed_0 = 0
|
|
overhang_speed_1 = 50
|
|
overhang_speed_2 = 40
|
|
overhang_speed_3 = 20
|
|
overhangs = 0
|
|
perimeter_acceleration = 3000
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0.45
|
|
perimeter_generator = arachne
|
|
perimeter_speed = 200
|
|
perimeters = 2
|
|
post_process =
|
|
print_settings_id =
|
|
raft_contact_distance = 0.1
|
|
raft_expansion = 1.5
|
|
raft_first_layer_density = 90%
|
|
raft_first_layer_expansion = 3
|
|
raft_layers = 0
|
|
resolution = 0.012
|
|
seam_position = aligned
|
|
single_extruder_multi_material_priming = 1
|
|
skirt_distance = 6
|
|
skirt_height = 1
|
|
skirts = 0
|
|
slice_closing_radius = 0.049
|
|
slicing_mode = regular
|
|
small_perimeter_speed = 130
|
|
solid_infill_acceleration = 4000
|
|
solid_infill_below_area = 15
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extruder = 1
|
|
solid_infill_extrusion_width = 0.42
|
|
solid_infill_speed = 100
|
|
spiral_vase = 0
|
|
staggered_inner_seams = 0
|
|
standby_temperature_delta = -5
|
|
support_material = 0
|
|
support_material_angle = 0
|
|
support_material_auto = 0
|
|
support_material_bottom_contact_distance = 0
|
|
support_material_bottom_interface_layers = -1
|
|
support_material_buildplate_only = 0
|
|
support_material_closing_radius = 2
|
|
support_material_contact_distance = 0.2
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0.35
|
|
support_material_interface_contact_loops = 0
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 3
|
|
support_material_interface_pattern = rectilinear
|
|
support_material_interface_spacing = 0
|
|
support_material_interface_speed = 100%
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 2.5
|
|
support_material_speed = 60
|
|
support_material_style = grid
|
|
support_material_synchronize_layers = 0
|
|
support_material_threshold = 0
|
|
support_material_with_sheath = 1
|
|
support_material_xy_spacing = 50%
|
|
support_tree_angle = 40
|
|
support_tree_angle_slow = 25
|
|
support_tree_branch_diameter = 2
|
|
support_tree_branch_diameter_angle = 5
|
|
support_tree_branch_diameter_double_wall = 3
|
|
support_tree_branch_distance = 1
|
|
support_tree_tip_diameter = 0.8
|
|
support_tree_top_rate = 15%
|
|
thick_bridges = 0
|
|
thin_walls = 0
|
|
threads = 16
|
|
top_fill_pattern = monotonic
|
|
top_infill_extrusion_width = 0.42
|
|
top_solid_infill_acceleration = 4000
|
|
top_solid_infill_speed = 200
|
|
top_solid_layers = 3
|
|
top_solid_min_thickness = 0
|
|
travel_acceleration = 10000
|
|
travel_speed = 350
|
|
travel_speed_z = 0
|
|
wall_distribution_count = 1
|
|
wall_transition_angle = 25
|
|
wall_transition_filter_deviation = 25%
|
|
wall_transition_length = 100%
|
|
wipe_tower = 0
|
|
wipe_tower_bridging = 10
|
|
wipe_tower_brim_width = 2
|
|
wipe_tower_cone_angle = 0
|
|
wipe_tower_extra_spacing = 100%
|
|
wipe_tower_extruder = 0
|
|
wipe_tower_no_sparse_layers = 0
|
|
wipe_tower_rotation_angle = 0
|
|
wipe_tower_width = 60
|
|
wipe_tower_x = 180
|
|
wipe_tower_y = 140
|
|
xy_size_compensation = 0
|
|
|
|
[filament:KINGROON ABS]
|
|
bed_temperature = 100
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 3
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 0.98
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 60
|
|
filament_colour = #29B2B2
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 0
|
|
filament_density = 0
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 25
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_toolchange_delay = 0
|
|
filament_type = ABS
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 100
|
|
first_layer_temperature = 230
|
|
full_fan_speed_layer = 5
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 80
|
|
min_fan_speed = 60
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 3
|
|
start_filament_gcode = ""
|
|
temperature = 230
|
|
|
|
[filament:KINGROON PLA]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 0.98
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 60
|
|
filament_colour = #29B2B2
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 0
|
|
filament_density = 0
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 25
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_toolchange_delay = 0
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 200
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 2
|
|
start_filament_gcode = ""
|
|
temperature = 200
|
|
|
|
[printer:KLP1 0.4 nozzle]
|
|
autoemit_temperature_commands = 0
|
|
bed_custom_model =
|
|
bed_custom_texture =
|
|
bed_shape = -6.95266e-310x-8.13251e-312,230x-8.13251e-312,230x230,-6.95266e-310x230
|
|
before_layer_gcode =
|
|
between_objects_gcode =
|
|
color_change_gcode = M600
|
|
cooling_tube_length = 5
|
|
cooling_tube_retraction = 91.5
|
|
default_filament_profile =
|
|
default_print_profile =
|
|
deretract_speed = 90
|
|
end_gcode = G91; relative positioning\n G1 Z1.0 F3000 ; move z up little to prevent scratching of print\n G90; absolute positioning\n G1 X0 Y200 F1000 ; prepare for part removal\n M104 S0; turn off extruder\n M140 S0 ; turn off bed\n G1 X0 Y200 F1000 ; prepare for part removal\n M84 ; disable motors\n M106 S0 ; turn off fan
|
|
extra_loading_move = -2
|
|
extruder_colour = ""
|
|
extruder_offset = 0x0
|
|
gcode_flavor = klipper
|
|
high_current_on_filament_swap = 0
|
|
host_type = prusalink
|
|
inherits =
|
|
layer_gcode =
|
|
machine_limits_usage = time_estimate_only
|
|
machine_max_acceleration_e = 10000,10000
|
|
machine_max_acceleration_extruding = 5000,1250
|
|
machine_max_acceleration_retracting = 5000,1250
|
|
machine_max_acceleration_travel = 1500,1250
|
|
machine_max_acceleration_x = 10000,10000
|
|
machine_max_acceleration_y = 10000,10000
|
|
machine_max_acceleration_z = 500,500
|
|
machine_max_feedrate_e = 120,120
|
|
machine_max_feedrate_x = 500,200
|
|
machine_max_feedrate_y = 500,200
|
|
machine_max_feedrate_z = 500,12
|
|
machine_max_jerk_e = 2.5,2.5
|
|
machine_max_jerk_x = 20,10
|
|
machine_max_jerk_y = 20,10
|
|
machine_max_jerk_z = 0.2,0.4
|
|
machine_min_extruding_rate = 0,0
|
|
machine_min_travel_rate = 0,0
|
|
max_layer_height = 0.32
|
|
max_print_height = 210
|
|
min_layer_height = 0.08
|
|
nozzle_diameter = 0.4
|
|
parking_pos_retraction = 92
|
|
pause_print_gcode = M601
|
|
print_host =
|
|
printer_model =
|
|
printer_notes =
|
|
printer_settings_id =
|
|
printer_technology = FFF
|
|
printer_variant =
|
|
printer_vendor =
|
|
printhost_apikey =
|
|
printhost_cafile =
|
|
remaining_times = 0
|
|
retract_before_travel = 1
|
|
retract_before_wipe = 70%
|
|
retract_layer_change = 1
|
|
retract_length = 1
|
|
retract_length_toolchange = 10
|
|
retract_lift = 0
|
|
retract_lift_above = 0
|
|
retract_lift_below = 0
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 90
|
|
silent_mode = 0
|
|
single_extruder_multi_material = 0
|
|
start_gcode = M104 S{first_layer_temperature[0]} ; set final nozzle temp\n\nM190 S{first_layer_bed_temperature[0]} ; set and wait for bed temp to stabilize\n\nM109 S{first_layer_temperature[0]} ; wait for nozzle temp to stabilize\nG28 ; h1ome all axes\n M117 ;Purge extruder\n G92 E0 ; reset extruder\n G1 Z1.0 F3000 ; move z up little to prevent scratching of surface\n G1 X2 Y20 Z0.3 F5000.0 ; move to start-line position\n G1 X2 Y175.0 Z0.3 F1500.0 E15 ; draw 1st line\n G1 X2 Y175.0 Z0.4 F5000.0 ; move to side a little\n G1 X2 Y20 Z0.4 F1500.0 E30 ; draw 2nd line\n G92 E0 ; reset extruder\n G1 Z1.0 F3000 ; move z up little to prevent scratching of surface\n
|
|
template_custom_gcode =
|
|
thumbnails = 100x100
|
|
thumbnails_format = PNG
|
|
toolchange_gcode =
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 1
|
|
use_volumetric_e = 0
|
|
variable_layer_height = 1
|
|
wipe = 1
|
|
z_offset = 0
|
|
|
|
[presets]
|
|
print = 0.2mm-KLP1
|
|
sla_print =
|
|
sla_material =
|
|
printer = KLP1 0.4 nozzle
|
|
filament = KINGROON PLA
|